ProECU USB Cable Programming Kit

The ProECU Programming Kit can be used by car enthusiasts, and owner clubs alike to both diagnose and program a wide variety of vehicles. They can only be purchased from any EcuTek Master Tuner.

Find a Master Tuner here
See what vehicles these kits support here

There are two options. Both kits require a Laptop and a wired connection from there to the OBD II port. The ProECU USB kit, pictured above right, has the interface included in the cable and the ECU Connect + Dongle kit, pictured above left, has a separate cable included to connect the laptop with the ECU Connect Interface.

At its simplest, the programming kit can be used for diagnostics and data logging. However, its most impressive feature is to allow EcuTek Master Tuners to tune customer vehicles remotely. The Master Tuner supplies suitable ROM files to the vehicle owner, who can use it to program these ROM files into their own car. If any fine-tuning is required, the customer can data-log the car and send the logs to the Master Tuner for their scrutiny and advice. The kit will program and log all EcuTek Supported vehicles.

ProECU Minimum Hardware Requirements

  • Operating System – Windows 10 or 11 Recommended. Windows 7 and 8.1 are supported, however some features may not be available. Running the software inside a virtual machine (such as Parallels or VMware) is not supported.
  • Processor – 1 Gigahertz or faster 32-bit or 64-bit (x86 CPU’s only, ARM based processors are unsupported)
  • Memory – 1 Gigabyte or greater
  • Hard Drive Space – 250mb ON C: Drive for ProECU programming kit. 2gb for ProECU Tuning Suites
  • Display – 1024×768 minimum screen resolution
  • Ports – Two free USB ports are required to allow use of the EcuTek Vehicle Interface and the Licence Key

ECU Connect + Dongle Extra Features

Our free ECU Connect App can be used to create dashboards, read and clear DTCs and control some of our custom RaceROM features in conjunction with our ECU Connect Interface. Find out more about ECU Connect here

Free Software

With the Programming Kit, you get FREE software included. So if you are competent enough to know your way around tuning a car and own either a Subaru BRZ/Toyota GT-86/Scion FR-S or Mazda Miata MX-5 Gen 3 (NC), then you can use the software to tune your own car. If your car has not been tuned on EcuTek before, a Flash Fee of 225 Flashpoints will be required for the Subaru/Toyota/Scion and 155 Flashpoints for the MX-5 Miata. These can be purchased from the Master Tuner who supplied the kit. Their contact details should be inside the kit.

Find out more about the FREE Software for Subaru BRZ/Toyota GT-86/Scion FR-S here.

Find out more about the FREE Software for the Mazda Miata MX-5 Gen 3 (NC) here.

*ProECU minimum hardware requirements

Upgrading your FREE Software

If you want to go further with the kit and bolt on a forced-induction kit to your car, you will need to upgrade the FREE software with the RaceROM pack. For the Subaru/Toyota/Scion, you will need RaceROM BRZ bolt-on, and for the MX-5 Miata, you will need the RaceROM MX-5 bolt-on. These are both available from the Master Tuner who supplied you with the kit.

Flashing your car with your Phone

The ProECU programming kit is available in both USB and ECU Connect wired versions. If you want to program your car from your phone over Bluetooth with no wires and no Laptop, you need PhoneFlash. Check out our PhoneFlash page to get yourself set up.

Find Your Local EcuTek Dealer
There are over 1,000 EcuTek dealers covering most countries in the world. If you want to get your car tuned, we have you covered.
Find An Authorized Dealer